Modification of Microstructure and Properties of Extruded Mg-Li-Al Alloys of α and α+ β Phase Composition using ECAP Processing

• Authors: J. Dutkiewicz , S. Rusz , W. Maziarz , W. Skuza , D. Kuc , O. Hilser
• Languages of publication: EN

Abstracts

EN

Two magnesium based alloys containing 4.5 wt% Li and 1.5 wt% Al (alloy 1) and 9 wt% Li and 1.5 wt% Al (alloy 2) were cast under argon atmosphere and hot extruded at 350°C. Microstructure of alloy 1 consisted of hexagonal α phase of average grain size 20 μm and small aluminum rich precipitates being the most probably AlLi₂Mg phase. Alloy 2 in the extruded form consisted of lamellas of α+ β phases of thickness 5-20 μm and length above 100 μm. Significant grain refinement down to about 2 μ m was observed in one-phase hexagonal (hcp) alloy 1 after one pass of ECAP processing with helical component. Two-phase (hcp + bcc) alloy 2 showed higher non-homogeneity after the first equal channel angular pressing pass due to easier deformation of softer bcc phase, while both, α and β phases exhibited low angle grain boundaries. The hardness and the yield strength of the alloys were higher for alloy 1 (68 HV and 205 MPa, respectively) than those of alloy 2 (61 HV and 175 MPa). Subsequent equal channel angular pressing passes were performed at lower extrusion stress. The hardness of both alloys did not change significantly after subsequent equal channel angular pressing passes and revealed tendency to decrease. Two-phase alloy showed superplastic properties already after one equal channel angular pressing pass at 160°C with grain growth after superplastic tensile testing. Single phase hcp alloy did not show such properties after 1 pass, but after a few equal channel angular pressing passes it could be superplastically formed.

Keywords

EN

83.50.-v; 81.40.Lm; 81.20.Fw

Discipline

• 81.20.Fw: Sol-gel processing, precipitation(for reactions in sol-gels, see 82.33.Ln; for sol-gels as disperse system, see 82.70.Gg)
• 83.50.-v: Deformation and flow
• 81.40.Lm: Deformation, plasticity, and creep(see also 83.50.-v Deformation and flow in rheology)

• Publisher: Institute of Physics, Polish Academy of Sciences
• Journal: Acta Physica Polonica A
• Year: 2017
• Volume: 131
• Issue: 5
• Pages: 1303-1306

Dates

published

2017-05

Contributors

author

J. Dutkiewicz

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, W.S. Reymonta 25, 30-059 Kraków, Poland

author

S. Rusz

• Technical University Ostrava, Department of Mechanical Engineering, 17 Listopadu 15, Ostrava, Czech Republic

author

W. Maziarz

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, W.S. Reymonta 25, 30-059 Kraków, Poland

author

W. Skuza

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, W.S. Reymonta 25, 30-059 Kraków, Poland

author

D. Kuc

• Silesian Technical University, Department of Metallurgy and Materials Science, Z. Krasińskiego 8, 40-019 Katowice, Poland

author

O. Hilser

• Technical University Ostrava, Department of Mechanical Engineering, 17 Listopadu 15, Ostrava, Czech Republic

References

• [1] Z. Drozd, Z. Trojanová, S. Kúdela, J. Alloys Comp. 378, 192 (2004), doi: 10.1016/j.jallcom.2004.01.040
• [2] G.H. Park, J.T. Kim, H.J. Park, Y.S. Kim, H.J. Jeong, N. Lee, Y. Seo, J.Y. Suh, H.T. Son, W.M. Wang, J.M. Park, K.B. Kim, J. Alloys Comp. 680, 116 (2016), doi: 10.1016/j.jallcom.2016.04.109
• [3] N. Saito, M. Mabuchi, M. Nakanishi, K. Kubota, K. Higashi, Scr. Mater. 36, 551 (1997)
• [4] M.V. Kral, B.C. Muddle, J.F. Nie, Mater. Sci. Eng. A 460-461, 227 (2007), doi: 10.1016/j.msea.2007.01.102
• [5] T. Liu, S.D. Wu, S.X. Li, P.J. Li, Mater. Sci. Eng. A 460-461, 499 (2007), doi: 10.1016/j.msea.2007.01.108
• [6] M. Furui, Ch. Xu, T. Aida, M. Inoue, H. Anada, T.G. Langdon, Mater. Sci. Eng. A 410-411, 439 (2005), doi: 10.1016/j.msea.2005.08.143
• [7] W.J. Kim, M.J. Kim, J.Y. Wang, Mater. Sci. Eng. A 516, 17 (2009), doi: 10.1016/j.msea.2009.03.089
• [8] H. Matsunoshita, K. Edalati, M. Furui, Z. Horita, Mater. Sci. Eng. A 640, 443 (2015), doi: 10.1016/j.msea.2015.05.103
• [9] J. Zhang, Yang Zhang, G. Wu, W. Liu, L. Zhang, W. Ding, Mater. Sci. Eng. A 621, 198 (2015), doi: 10.1016/j.msea.2014.10.076
• [10] Z. Trojanova, Z. Drozd, P. Lukac, F. Chmelik, Mater. Sci. Eng. A 410-411, 148 (2005), doi: 10.1016/j.msea.2005.08.088

Identifiers

DOI

10.12693/APhysPolA.131.1303