Journal
Article title
Authors
Title variants
Languages of publication
Abstracts
The aim of this study was to investigate the influence of cutting parameters and effect of graphite rate on cutting force and surface roughness in drilling of Al/20%SiC/5%Gr, Al/20%SiC/7.5%Gr and Al /20%SiC/10%Gr hybrid composites, fabricated by vortex method. The drilling tests are conducted with diamond-like-carbon coated cutting tools. The Grey relational analysis based Taguchi optimization method was selected to determine the optimum cutting conditions. The results show that the spindle speed (4500 rpm), the rate of graphite (10%) and feed (0.1 mm/rev) were found to be significant parameters for surface roughness and cutting force. The predicted values from the developed model and experimental values are found to be very similar in this study.
Keywords
Journal
Year
Volume
Issue
Pages
551-554
Physical description
Dates
published
2017-03
Contributors
author
- Marmara University, Faculty of Technology, Department of Mechanical Engineering, 34722, Istanbul, Turkey
author
- Abant Izzet Baysal University, Faculty of Engineering and Architecture, Mechanical Engineering, 14280, Bolu, Turkey
author
- Marmara University, Faculty of Technology, Department of Mechanical Engineering, 34722, Istanbul, Turkey
References
- [1] Y. Altunpak, M. Ay, S. Aslan, Int. J. Adv. Manuf. Technol. 60, 513 (2012), doi: 10.1007/s00170-011-3644-4
- [2] S.V. Prasad, R. Asthana, Tribol. Lett. 17, 445 (2004), doi: 10.1023/B:TRIL.0000044492.91991.f3
- [3] M.T. Hayajneh, A.M. Hassan, A.T. Mayyas, J. Alloy Comp. 478, 559 (2009), doi: 10.1016/j.jallcom.2008.11.155
- [4] S. Basavarajappa, G. Chandramohan, A. Mahadevan, M. Thangavelu, R. Subramanian, P. Gopalakrishnan, Wear 262, 1007 (2007), doi: 10.1016/j.wear.2006.10.016
- [5] D. Gultekin, M. Uysal, S. Aslan, M. Alaf, M.O. Guler, H. Akbulut, Wear 270, 73 (2010), doi: 10.1016/j.wear.2010.09.001
- [6] N. Kumar, G. Gautam, R.K. Gautam, A. Mohan, S. Mohan, J. Inst. Eng. India Ser. D 97, 233 (2016), doi: 10.1007/s40033-015-0091-7
- [7] A. Premnath, Particul. Sci. Technol. 34, 707 (2016), doi: 10.1080/02726351.2015.1112327
- [8] S.C. Sharma, B.M. Girish, R.S. Kulkarni, R. Kamath, HUKHUKNML Tech J. 38, 127 (1996)
- [9] S. Basavarajappa, G. Chandramohan, J.P. Davim, Int. J. Mach. Tool. Manufact. 47, 92 (2007), doi: 10.1016/j.ijmachtools.2006.02.008
- [10] A.M. Raj, S.L. Das, K. Palanikumarr, Indian J. Sci. Technol. 6, 5002 (2013)
- [11] M. El-Gallab, M. Sklad, J. Mater. Proc. Technol. 83, 277 (1998), doi: 10.1016/S0924-0136(98)00072-7
- [12] T. Rajmohan, K. Palanikumar, M. Kathirvel, Trans. Nonferrous Met. Soc. China 22, 1286 (2012), doi: 10.1016/S1003-6326(11)61317-4
- [13] A.M. Ali, E.Y.T. Adesta, D. Augusman, S.N.M. Badari, M.H.F. Al-Hazza, Asian J. Scient. Res. 4, 255 (2011), doi: 10.3923/AJSR.2011.255.263
- [14] M. Ay, Y. Altunpak, J. Eng. Fundament. 2, 42 (2015), doi: 10.17530/jef.15.17.2.2
- [15] G. Tosun, Int. J. Adv. Manuf. Technol. 55, 477 (2011), doi: 10.1007/s00170-010-3103-7
- [16] W.H. Yang, Y.S. Tarng, Int. J. Mater. Process Technol. 84, 122 (1998), doi: 10.1016/S0924-0136(98)00079-X
- [17] T. Chung-Chen, H. Honk, Int. J. Mater. Processing Technol. 123, 1 (2002), doi: 10.1016/S0924-0136(01)01152-9
- [18] K. Venkatesan, R. Ramanujam, V. Saxena, N. Chawdhury, V. Choudhary, ARPN J. Eng. Appl. Sci. 9, 250 (2014) http://www.arpnjournals.com/jeas/research_papers/rp_2014/jeas_0314_1023.pdf
- [19] M. Kurt, S. Hartomacioğlu, B. Mutlu, U. Köklü, Mater. Technol. 46, 205 (2012) http://mit.imt.si/Revija/izvodi/mit123/kurt.pdf
- [20] H. Ravikumar, P.L. Arun, S. Thileepan, Int. J. ChemTech. Res. 8, 292 (2015) http://sphinxsai.com/2015/ch_vol8_no12/1/(292-303)V8N12CT.pdf
Document Type
Publication order reference
Identifiers
YADDA identifier
bwmeta1.element.bwnjournal-article-appv131n359kz