PL EN


Preferences help
enabled [disable] Abstract
Number of results
2017 | 131 | 3 | 354-358
Article title

Optimization of Cutting Parameters, Condition and Geometry in Turning AISI 316L Stainless Steel Using the Grey-Based Taguchi Method

Authors
Content
Title variants
Languages of publication
EN
Abstracts
EN
In this study, experimental optimization of cutting forces, surface roughness and the hardness of material after turning of AISI 316L stainless steel, using conventional and wiper insert cutting tools under dry, CO₂ and MQL cutting conditions, is presented. The influences of feed rate, cutting depth, and cooling system on surface roughness, cutting force and material hardness were examined. In order to optimize the turning process, Grey relational analysis optimization method was used. The optimal machinability parameters of AISI 316L stainless steel with coated carbide insert were successfully determined.
Keywords
EN
Year
Volume
131
Issue
3
Pages
354-358
Physical description
Dates
published
2017-03
References
  • [1] T. Kosa, P. Ronald, Handbook: Machining, Vol. 16, 9th ed., 1989
  • [2] R. M'Saoubi, J.C. Outeiro, B. Changeux, J.L. Lebrun, A.M. Dias, J. Mater. Proc. Tech. 96, 225 (1999), doi: 10.1016/S0924-0136(99)00359-3
  • [3] J.D. Darwin, D.M. Lal, G. Nagarajan, J. Mater. Proc. Tech. 195, 241 (2008), doi: 10.1016/j.jmatprotec.2007.05.005
  • [4] J.C. Outeiro, D. Umbrello, R. M'Saoubi, Int. J. Mach. Tools Manufact., 46, 1786 (2006), doi: 10.1016/j.ijmachtools.2005.11.013
  • [5] B.K. Agrawal, Introduction to Engineering Materials, Mc Graw-Hill, 1983
  • [6] C. Maranhao, J.P. Davim, Simulation Modelling Practice and Theory 18, 139 (2010), doi: 10.1016/j.simpat.2009.10.001
  • [7] I. Korkut, M. Boy, I. Karacan, U. Seker, Mater. Design 28, 2329 (2007), doi: 10.1016/j.matdes.2006.07.009
  • [8] İ. Ciftci, Tribol. Int. 39, 565 (2006), doi: 10.1016/j.triboint.2005.05.005
  • [9] Ö. Tekaslan, N. Gerger, M. Günay, U. Şeker, Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi 13, 135 (2007) http://www.journalagent.com/pajes/pdfs/PAJES_13_2_135_144.pdf
  • [10] Z. Tekiner, S. Yeşilyurt, Mater. Design 25, 507 (2004), doi: 10.1016/j.matdes.2003.12.011
  • [11] M. Kaladhar, K.V. Subbaiah, C.S. Rao, J. Engin. Sci. Technol. 8, 165 (2013) http://jestec.taylors.edu.my/Vol%208%20Issue%202%20April%2013/Volume%20(8)%20Issue%20(2)%20165-176.pdf
  • [12] S. Li, Y. Liu, R. Zhu, H. Li, W. Ding, Appl. Mech. Mater. 34, 1829 (2010), doi: 10.4028/www.scientific.net/AMM.34-35.1829
  • [13] D.P. Selvaraj, P. Chandramohan, J. Engin. Sci. Technol. 5, 293 (2010) http://jestec.taylors.edu.my/Vol%205%20Issue%203%20September%2010/Vol_5_3_293_301_DP_Selvaraj.pdf
  • [14] A.E. Diniz, J.R. Ferreira, F.T. Filho, Int. J. Mach. Tools Manufact. 43, 317 (2003), doi: 10.1016/S0890-6955(02)00186-4
  • [15] H.A. Kishawy, M. Dumitrescu, E.G. Ng, M.A. Elbestawi, Int. J. Mach. Tools Manufact. 45, 219 (2005), doi: 10.1016/j.ijmachtools.2004.07.003
  • [16] N.R. Dhar, M. Kamruzzaman, M. Ahmed, J. Mat. Proc. Technol. 172, 299 (2006), doi: 10.1016/j.jmatprotec.2005.09.022
  • [17] F. Itoigawa, T.H.C. Childs, T. Nakamura, W. Belluco, Wear 260, 339 (2006), doi: 10.1016/j.wear.2005.03.035
  • [18] N.R. Dhar, M.W. Islam, S. Islam, M.A.H. Mithu, J. Mater. Proc. Tech. 171, 93 (2006), doi: 10.1016/j.jmatprotec.2005.06.047
  • [19] E.O. Ezugwu, J. Bonney, R.B. Da Silva, O. Çakir, Int. J. Mach. Tools Manufact. 47, 884 (2007), doi: 10.1016/j.ijmachtools.2006.08.005
  • [20] A. Attanasio, M. Gelfi, C. Giardini, C. Remino, Wear 260, 333 (2006), doi: 10.1016/j.wear.2005.04.024
  • [21] C. Bruni, A. Forcellese, F. Gabrielli, M. Simoncini, Int. J. Machine Tools Manufact. 46, 1547 (2006), doi: 10.1016/j.ijmachtools.2005.09.007
  • [22] K. Venkatesan, R. Ramanujam, V. Saxena, N. Chawdhury, V. Choudhary, J. Engin. Appl. Sci. 9, 250 (2014) http://arpnjournals.com/jeas/research_papers/rp_2014/jeas_0314_1023.pdf
  • [23] J. Liu, R. Han, Y. Sun, Int. J. Mach. Tools Manufact. 45, 687 (2005), doi: 10.1016/j.ijmachtools.2004.09.022
  • [24] M. Stanford, P.M. Lister, C. Morgan, K.A. Kibble, J. Mat. Proc. Technol. 209, 961 (2009), doi: 10.1016/j.jmatprotec.2008.03.003
  • [25] P.J. Ross, Taguchi Techniques for Quality Engineering, 1996
  • [26] N. Tosun, Int. J. Adv. Manufact. Technol. 28, 450 (2006), doi: 10.1007/s00170-004-2386-y
  • [27] İ. Asiltürk, S. Neşeli, Measurement 45, 785 (2012), doi: 10.1016/j.measurement.2011.12.004
  • [28] M. Kurt, S. Hartomacioğlu, B. Mutlu, U. Köklü, Mater. Technol. 46, 205 (2012) http://mit.imt.si/Revija/izvodi/mit123/kurt.pdf
Document Type
Publication order reference
YADDA identifier
bwmeta1.element.bwnjournal-article-appv131n308kz
Identifiers
JavaScript is turned off in your web browser. Turn it on to take full advantage of this site, then refresh the page.