The Surface Properties of WC-Co-Cr Based Coatings Deposited by High Velocity Oxygen Fuel Spraying

• Authors: Y. Ozbek , N. Canikoğlu , M. İpek
• Languages of publication: EN

Abstracts

EN

The aim of this research was to investigate microstructural and mechanical properties of the WC-Co-Cr coatings by high velocity oxygen fuel spraying. Woka 3653 (WC10Co4Cr) powder was used as coating material. This powder is widely used as a tribological coating material providing a combination of high toughness, high hardness, and good strength. The coatings were produced for the different high velocity oxygen fuel spraying parameters. The treated samples were characterized by using scanning electron microscopy/energy dispersive X-ray spectrometry and X-ray diffractometry. Microhardness measurements were executed to evaluate the mechanical properties of the coatings. Also the wear performance of the coatings was investigated. The scanning electron microscopy and energy dispersive X-ray spectrometry analyses were applied to worn surfaces. The results indicated that the coating shows slightly higher microhardness and better abrasive wear resistance than the conventional counterpart.

Keywords

EN

81.15.Rs

Discipline

• 81.15.Rs: Spray coating techniques

• Publisher: Institute of Physics, Polish Academy of Sciences
• Journal: Acta Physica Polonica A
• Year: 2017
• Volume: 131
• Issue: 1
• Pages: 186-189

Dates

published

2017-01

Contributors

author

Y. Ozbek

• Sakarya University, Engineering Faculty, Department of Metallurgical and Materials Engineering, Esentepe Campus, 54187, Sakarya, Turkey

author

N. Canikoğlu

• Sakarya University, Engineering Faculty, Department of Metallurgical and Materials Engineering, Esentepe Campus, 54187, Sakarya, Turkey

author

M. İpek

• Sakarya University, Engineering Faculty, Department of Metallurgical and Materials Engineering, Esentepe Campus, 54187, Sakarya, Turkey

References

• [1] V.K. Balla, S. Bose, A. Bandyopadhyay, Mater. Sci. Eng. A 527, 6677 (2010), doi: 10.1016/j.msea.2010.07.006
• [2] M. Afzal, M. Ajmal, A. Nusair Khan, A. Hussain, R. Akhter, Opt. Laser Technol. 56, 202 (2014), doi: 10.1016/j.optlastec.2013.08.017
• [3] A. Kumar, A. Sharma, S.K. Goel, Appl. Surf. Sci. 370, 418 (2016), doi: 10.1016/j.apsusc.2016.02.163
• [4] C.W. Lee, J.H. Han, J. Yoon, M.C. Shin, S.I. Kwun, Surf. Coat. Technol. 204, 2223 (2010), doi: 10.1016/j.surfcoat.2009.12.014
• [5] J.A.R. Wesmann, N. Espallargas, Tribol. Int. 101, 301 (2016), doi: 10.1016/j.triboint.2016.04.032
• [6] M. Jafari, M.H. Enayat, M. Salehi, S.M. Nahvi, C.G. Park, Mater. Sci. Eng. A 578, 46 (2013), doi: 10.1016/j.msea.2013.04.064
• [7] E. Bemporad, M. Sebastiani, F. Casadei, F. Carassiti, Surf. Coat. Technol. 201, 7652 (2007), doi: 10.1016/j.surfcoat.2007.02.041
• [8] T. Sahraoui, S. Guessasma, M.A. Jeridane, M. Hadji, Mater. Des. 31, 1431 (2010), doi: 10.1016/j.matdes.2009.08.037
• [9] J. Yuan, C. Ma, S. Yang, Z. Yu, H. Li, Surf. Coat. Technol. 285, 17 (2016), doi: 10.1016/j.surfcoat.2015.11.017
• [10] J.A. Picas, Y. Xiong, M. Punset, L. Ajdelsztajn, A. Forn, J.M. Schoenung, Int. J. Refract. Met. Hard Mater. 27, 344 (2009), doi: 10.1016/j.ijrmhm.2008.07.002
• [11] K. Kumari, K. Anand, M. Bellacci, M. Giannozzi, Wear 268, 1309 (2010), doi: 10.1016/j.wear.2010.02.001
• [12] Y. Wu, S. Hong, J. Zhang, Z. He, W. Guo, Q. Wang, G. Li, Int. J. Refract. Met. Hard Mater. 3, 21 (2012), doi: 10.1016/j.ijrmhm.2012.01.002
• [13] U. Selvadurai, P. Hollingsworth, I. Baumann, B. Hussong, W. Tillmann, S. Rausch, D. Biermann, Surf. Coat. Technol. 26, 30 (2015), doi: 10.1016/j.surfcoat.2014.11.055
• [14] G. Bolelli, L. Lusvarghi, M. Barletta, Wear 267, 944 (2009), doi: 10.1016/j.wear.2008.12.06
• [15] N. Ma, L. Guo, Z. Cheng, H. Wu, F. Ye, K. Zhang, Appl. Surf. Sci. 320, 364 (2014), doi: 10.1016/j.apsusc.2014.09.081

Identifiers

DOI

10.12693/APhysPolA.131.186