Micro-Abrasion Wear Behavior of Thermal-Spray-Coated Steel Tooth Drill Bits

• Authors: A. Günen
• Languages of publication: EN

Abstracts

EN

Wear behavior of four kinds of thermally sprayed coatings on steel tooth drill bits have been investigated by micro-abrasion wear test. The fixed ball micro abrasion wear test was applied for bare substrate and for thermal sprayed substrate of each sample. SiC and Al₂O₃ abrasive powders with grain size of 5 μm were used in the abrasion experiments. Ball rotational speed values of 140 rpm and applied loads of 1, 2 and 3 N were used. Experimental results show that the wear mechanisms of the coatings are micro-grooving and micro-rolling. Application of the coatings was found to have an influence on the wear mechanism of the samples. The results also indicate that wear resistance of thermally sprayed coatings can be correlated to porosity, hardness, plasticity, toughness, and cohesion properties of the coatings. In addition, wear resistance of the coated samples had increased in accordance with the increasing coating thickness.

Keywords

EN

81.05.Bx; 82.35.Gh; 81.65.Kn

Discipline

• 82.35.Gh: Polymers on surfaces; adhesion(see also 68.35.Np Adhesion in surfaces and interfaces)
• 81.05.Bx: Metals, semimetals, and alloys
• 81.65.Kn: Corrosion protection(see also 82.45.Bb Corrosion and passivation in electrochemistry)

• Publisher: Institute of Physics, Polish Academy of Sciences
• Journal: Acta Physica Polonica A
• Year: 2016
• Volume: 130
• Issue: 1
• Pages: 217-222

Dates

published

2016-07

Contributors

author

A. Günen

• Iskenderun Tech. Univ., Faculty of Technology, Materials Engineering Department, Hatay, Turkey

References

• [1] P.X. Moore, Drilling Practices Manual, 2nd ed., PennWell Publishing Company Oklahoma, USA 1986, p. 363
• [2] R.E. Grimes, E.C. Felderhoff, H. Brown, Oil Gas J. 18, 76 (1992), doi: 10.1016/0148-9062(92)91878-9
• [3] R.A. Bobo, J. Petr. Tech. 20, 700 (1968), doi: 10.2118/1843-PA
• [4] K.W. Cummins, Technical Report No 28, Michigan State Univ. Inst. of Water Research, 1973
• [5] D. Praillet, World Mining Equipments Sept., 20 (1998)
• [6] K. Teii, T. Hori, S. Matsumoto, Thin Solid Films 519, 1817 (2011), doi: 10.1016/j.tsf.2010.10.017
• [7] I. Mrochek, R. Gunzel, W. Matz, W. Moller, V. Anishchik, Nukleonika 44, 217 (1999)
• [8] L.D. Yu, G.W. Shuy, T. Vilaithong, Surf. Coat. Technol. 128-129, 404 (2000), doi: 10.1016/S0257-8972(00)00642-3
• [9] A. Kolitsch, E. Richter, Cryst. Res. Technol. 18, 5 (1983), doi: 10.1002/crat.2170180122
• [10] M.J. Kupczyk, P. Siwak, J. ASTM Int. 8, 1 (2011)
• [11] N.J. Kar, IADUSPE Drilling Conj., 1990, p. 49, doi: 10.2118/19910-MS
• [12] M.W. Richert, B. Mikułowski, P. Pałka, A. Hotloś, M. Perek-Nowak, J. Surf. Eng. Mat. Adv. Techn. 3, 1 (2013), doi: 10.4236/jsemat.2013.31001
• [13] P. Fauchais, A. Vardelle, in: Advanced Plasma Spray Applications, Ed. H. Jazi, InTech, 2012, doi: 10.5772/34448
• [14] A.C. Karaoglanli, Sci. Adv. Mater. 7, 173 (2015), doi: 10.1166/sam.2015.2099
• [15] A.C. Karaoglanli, B. Demirel, A. Turk, R. Varol, K.M. Doleker, Appl. Surf. Sci. 354, 314 (2015), doi: 10.1016/j.apsusc.2015.06.113
• [16] R.I. Trezona, D.N. Alsopp, I.M. Hutchings, Wear 225, 205 (1999), doi: 10.1016/S0043-1648(98)00358-5
• [17] M.M. Stack, M. Mathew, Wear 255, 14 (2003), doi: 10.1016/S0043-1648(03)00204-7
• [18] M.M. Stack, H. Jawan, M.T. Mathew, Tribol. Int. 9, 848 (2005), doi: 10.1016/j.triboint.2005.02.013
• [19] M.M. Stack, M. Mathew, C. Hodge, Electrochim. Acta 56, 8249 (2011), doi: 10.1016/j.electacta.2011.06.064
• [20] A.C. Karaoglanli, Materials Technol. 49, 253 (2015)
• [21] A. Kassman, S. Jacobson, S. Erickson, P. Olsson, M. Hedenqvist, Surf. Coat. Technol. 50, 75 (1991), doi: 10.1016/0257-8972(91)90196-4
• [22] X.Z. Ding, C.T. Bui, X.T. Zeng, Surf. Coat. Technol. 203, 680 (2008), doi: 10.1016/j.surfcoat.2008.08.019
• [23] A. Günen, M.S. Gök, A. Erdoğan, B. Kurt, N. Orhan, Tribol. Trans. 56, 400 (2013), doi: 10.1080/10402004.2012.756566
• [24] K.T. Kembaiyan, K. Keshavan, Wear 186-187, 487 (1995), doi: 10.1016/0043-1648(95)07142-3
• [25] G. Bolelli, L. Lusvarghi, R. Giovanardi, Surf. Coat. Tech. 202, 4793 (2008), doi: 10.1016/j.surfcoat.2008.04.056
• [26] R. Pileggi, M.M. Tului, D. Stocchi, S. Lionetti, Surf. Coat. Tech. 268, 247 (2015), doi: 10.1016/j.surfcoat.2014.10.007
• [27] D.A. Stewart, P.H. Shipway, D.G. McCartney, Acta Mater. 48, 1593 (2000)
• [28] J.K.N. Murthy, B. Venkataraman, Surf. Coat. Tech. 200, 642 (2006), doi: 10.1016/j.surfcoat.2004.10.136
• [29] P. Vuoristo, K. Niemi, A. Makela, T. Mantyla, Proc. 7th National Thermal Spray Conference, Boston, Massachusetts, 1994, p. 121
• [30] A. Karimi, Ch. Verdon, Surf. Coat. Tech. 57, 81 (1993)
• [31] H. Sin, N. Saka, P. Suh, Wear 55, 163 (1979), doi: 10.1016/0043-1648(79)90188-1
• [32] D.L. Duan, S. Li, X.H. Duan, Z.S. Li, Tribol. Trans. 48, 45 (2005), doi: 10.1080/05698190590896915
• [33] M.S. Gok, Y. Kucuk, V. Koc, O. Gencel, W. Brostow, Mech. Adv. Mater. Struc. 18, 389 (2011), doi: 10.1080/15376494.2011.563413
• [34] K.I. Schiffmann, R. Bethke, N. Kristen, Surf. Coat. Techn. 200, 2348 (2005), doi: 10.1016/j.surfcoat.2005.01.015
• [35] I.M. Hutchings, Tribol. Intern. 31, 5 (1998), doi: 10.1016/S0301-679X(98)00004-8
• [36] ASTM G77-05 Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test (2010)

Identifiers

DOI

10.12693/APhysPolA.130.217