The Prediction and Optimization of the Effects of Abrasive Waterjet Cutting Parameters On Kerf

• Authors: M. Ay , İ. Ay
• Languages of publication: EN

Abstracts

EN

In this study, Inconel 718 material, which is widely used in space aircraft and defense industry and is difficult to be processed by traditional methods, has been cut off with abrasive water-jet. The effects of cutting parameters such as pressure, cutting speed, abrasive consumption and cutting height on kerf have been studied. The input levels needed to be used to obtain the minimum kerf have been determined through Taguchi analysis and the experimental test. The setup of experiment was modelled using linear regression model and an artificial neural network and the results were compared. It was seen that the artificial neural network model gives better results when compared to regression model. The results of experimental test to which the related models were applied are satisfactory.

Keywords

EN

07.05.Mh

Discipline

• 07.05.Mh: Neural networks, fuzzy logic, artificial intelligence

• Publisher: Institute of Physics, Polish Academy of Sciences
• Journal: Acta Physica Polonica A
• Year: 2016
• Volume: 129
• Issue: 4
• Pages: 762-766

Dates

published

2016-04

Contributors

author

M. Ay

• Marmara University, Faculty of Technology, Department of Mechanical Engineering 34722 İstanbul, Turkey

author

İ. Ay

• Marmara University, Institute of Pure and Applied Sciences, 34722 İstanbul, Turkey

References

• [1] N. Geren, T. Tunç, Mühendis Ve Makine Dergisi 42, 500 (2001) http://mmo.org.tr/resimler/dosya_ekler/c9ac0159c94d8d0_ek.pdf?dergi=33
• [2] M.K. Külekçi, A. Akkurt, Niğde Üniversitesi Mühendislik Bilimleri Dergisi 5, 13 (2001)
• [3] G. Aydın, İ. Karakurt, K. Aydıner, Madencilik 49, 17 (2010) http://maden.org.tr/resimler/ekler/2d90d223cf3e223_ek.pdf
• [4] S. Mezarcıöz, R.T. Oğulata, Tekstil Ve Konfeksiyon, 4 (2010) http://tekstilvekonfeksiyon.com/suprem-kumaslarda-patlama-mukavemeti-degerinin-taguchi-ortogonal-dizayna-gore-optimizasyonu-248.html
• [5] İ. Ay, Süper Alaşımların Aşındırıcılı Sujeti İle İşlenebilirliğinin Araştırılması, Marmara University, Master Thesis, 2010
• [6] R.R. Kanjit, A Primer on the Taguchi Method Cover, Van Nostrand Reinhold, New York (1990)
• [7] N. Sakarya, C.Göloğlu, Gazi Üniv. Müh. Mim. Fak. Der. 21, 603 (2006) http://mmfdergi.gazi.edu.tr/article/view/1061000733
• [8] M. Sönmez, Sayısal Analiz Ders Notları, Aksaray Üniversitesi İnşaat Mühendisliği Bölümü, 2008
• [9] M. Demetgül, O. Yazıcıoğlu, Teknoloji 9, 101 (2006) http://jestech.karabuk.edu.tr/arsiv/1302-0056/TEKNOLOJI%20ARCHIVE.pdf
• [10] H.S. Ergür, Eskişehir Osmangazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi XXII, 2 (2009) http://mmfdergi.ogu.edu.tr/mmfdrg/2009-2/11.pdf
• [11] M.H.Sazlı, H.Tanrıkulu, XII. Türkiye'de İnternet Konferansı 8-10 Kasım 2007 Bildiriler Kitabı, Ankara, 2007, p. 217 http://inet-tr.org.tr/inetconf12/kitap/Bildiriler/45_39_inet07.pdf
• [12] J.J.R. Jegaraj, N.R. Babu, Int. J. Mach. Tool. Manu. 45, 1443 (2005), doi: 10.1016/j.ijmachtools.2005.01.020
• [13] D.K. Shanmugam, S.H. Masood, J. Mater. Process. Techn. 209, 3887 (2009), doi: 10.1016/j.jmatprotec.2008.09.001
• [14] J. Wang, W.C.K. Wong, Int. J. Mach. Tool. Manu. 39, 855 (1999), doi: 10.1016/S0890-6955(98)00078-9
• [15] V. Gupta, P.M. Pandey, M.P. Garg, R. Khanna, N.K. Batra, Procedia Mater. Sci. 6, 140 (2014), doi: 10.1016/j.mspro.2014.07.017
• [16] M. Ay, U. Çaydaş, A. Hasçalık, Mater. Manuf. Process. 25, 1160 (2010), doi: 10.1080/10426914.2010.502953
• [17] A. Haşçalik, U. Çaydaş, H. Gürün, Material. Design 28, 1953 (2007), doi: 10.1016/j.matdes.2006.04.020

Identifiers

DOI

10.12693/APhysPolA.129.762