Influence of Parameters on Dry Sliding of Chopped Bamboo Reinforced Epoxy Composites Based on the Taguchi Method

• Authors: N. Ozsoy , M. Ozsoy , A. Mimaroglu
• Languages of publication: EN

Abstracts

EN

Chopped bamboo-reinforced epoxy composites were fabricated and tested to investigate their tribological properties. Three different weight fractions of 6%, 8% and 10% were used as reinforcement in the composites. Wear behaviour of composites was investigated by pin on disc wear testing device. To analyse the results the design of experiments (DOE) approach by using the Taguchi method was employed. Three different parameters (load, sliding speed, weight fractions) with three levels were chosen in design of experiments. Signal to noise ratio and analysis of variance (ANOVA) were used to investigate the influence of parameters on the wear rate and the coefficient of friction. According to the results, load was the most effective parameter for both wear rate and coefficient of friction.

Keywords

EN

81.05.Qk; 07.05.Fb; 62.20.Qp

Discipline

• 62.20.Qp: Friction, tribology, and hardness(see also 46.55.+d Tribology and mechanical contacts in continuum mechanics of solids; for materials treatment effects on friction related properties, see 81.40.Pq)
• 07.05.Fb: Design of experiments
• 81.05.Qk: Reinforced polymers and polymer-based composites

• Publisher: Institute of Physics, Polish Academy of Sciences
• Journal: Acta Physica Polonica A
• Year: 2016
• Volume: 129
• Issue: 4
• Pages: 687-689

Dates

published

2016-04

Contributors

author

N. Ozsoy

• Sakarya University, Faculty of Engineering, Mechanical Engineering Department, Serdivan, Sakarya

author

M. Ozsoy

• Sakarya University, Faculty of Engineering, Mechanical Engineering Department, Serdivan, Sakarya

author

A. Mimaroglu

• Sakarya University, Faculty of Engineering, Mechanical Engineering Department, Serdivan, Sakarya

References

• [1] P. Kongkeaw, W. Nhuapeng, W. Thamajaree, J. Microscopy Society Thailand 4, 46 (2011)
• [2] K. Gupta, Mater. Design 35, 467 (2012), doi: 10.1016/j.matdes.2011.09.010
• [3] A.K. Mishra, R. Sheokand, R.K. Srivastava, Int. J. Sci. Res. Publ. 2, 1 (2012)
• [4] S.V. Prasat, R. Subramanian, N. Radhika, B. Anandavel, L. Arun, N. Praveen, Eur. J. Sci. Res. 53, 280 (2011)
• [5] T.R. Hemanth Kumar, R.P. Swamyand, T.K. Chandrashekar, J. Miner. Mater. Character. Eng. 10, 1179 (2011), doi: 10.4236/jmmce.2011.1012090
• [6] S. Basavarajappa, G. Chandramohan, J. Mater. Sci. Technol. 21, 845 (2005)
• [7] S. Koksal, F. Ficici, O. Savas, Mater. Design 42, 124 (2012), doi: 10.1016/j.matdes.2012.05.048
• [8] Y. Sahin, Tribol. Int. 43, 939 (2010), doi: 10.1016/j.triboint.2009.12.056
• [9] Y. Sahin, Mater. Sci. Eng. A 408, 1 (2005), doi: 10.1016/j.msea.2004.11.012
• [10] G. Taguchi, Taguchi on Robust Technology Development, ASME, New York 1993, doi: 10.1115/1.800288
• [11] C. Soutis, Mater. Sci. Eng. A 412, 171 (2005), doi: 10.1016/j.msea.2005.08.064
• [12] K. Palanikumar, Int. J. Adv. Manu. Technol. 36, 19 (2008), doi: 10.1007/s00170-006-0811-0

Identifiers

DOI

10.12693/APhysPolA.129.687