Preferences help
enabled [disable] Abstract
Number of results
2015 | 128 | 4 | 629-632
Article title

Tool Steels: Forging Simulation and Microstructure Evolution of Large Scale Ingot

Title variants
Languages of publication
The aim of this paper is to analyze the hot working behavior of two different steels based on 3% and 5% Cr steel chemistry, respectively. Hot deformation is studied by hot torsion tests in the range of temperatures 1000-1200°C and strain rates 0.01, 0.10, 1.00 s^{-1}. At given temperatures and strain rates flow curves exhibit a peak followed by a decline towards a steady state which is indicative of dynamic recrystallization. At constant strain, flow stress increases with increasing strain rate and decreasing temperature. The analysis of the constitutive equation relating peak flow stress, strain rate and temperature shows high activation energy values for both steels. Recrystallized volume fraction of steels after hot deformation is estimated based on the grain orientation spread as measured by electron backscattered diffraction technique, on the hot deformed and quenched materials.
  • Università degli Studi di Perugia, Via G. Duranti 63, I06125 Perugia, Italy
  • Università degli Studi di Perugia, Via G. Duranti 63, I06125 Perugia, Italy
  • Società delle Fucine, Viale B. Brin 218, I05100 Terni, Italy
  • Società delle Fucine, Viale B. Brin 218, I05100 Terni, Italy
  • Centro Sviluppo Materiali S.p.A., Via di Castel Romano 100, I00128 Roma, Italy
  • Concordia University, 1455 Maisonneuve W. EV 3.420, Montreal, H3G 1M8, Canada
  • [1] H.J. McQueen, E. Evangelista, in: Proc. 2nd Int. Conf. on Superhigh Strength Steels, Milano (Italy), 2010
  • [2] E. Evangelista, M. Masini, M. El Methedi, S. Spigarelli, J. Alloys Comp. 378, 151 (2004), doi: 10.1016/j.jallcom.2003.11.170
  • [3] H.J. McQueen, J.J. Jonas, Metal Forming: Interrelation between Theory and Practice, Plenum Press, New York 1971, doi: 10.1007/978-1-4615-1757-3
  • [4] T. Sakai, A. Belyakov, R. Kuibyshev, H. Miura, J.J. Jonas, Prog. Mater. Sci. 60, 130 (2014), doi: 10.1016/j.pmatsci.2013.09.002
  • [5] C. Imbert, N.D. Ryan, H.J. McQueen, Metall. Mater. Trans. A 15, 1855 (1984), doi: 10.1007/BF02664899
  • [6] C. Imbert, H.J. McQueen, Mater. Sci. Tech. Ser. 16, 532 (2000)
  • [7] H.J. McQueen, A.C. Imbert, in: Proc. Int. Conf. Thermomechanical Processing and Mechanical Properties of Hypereutectoid Steels, Warrendale, 1997, TMS-AIME, p. 55
  • [8] H.J. McQueen, E. Evangelista, N. Ryan, in: Proc. Int. Conf. on Thermomechanical Processing: Mechanics, Microstructure and Control, Sheffield, 2003, p. 359
  • [9] M.F. Abbod, C.M. Sellars, A. Tanaka, D.A. Linkens, M. Mahfouf, Mater. Sci. Eng. A 491, 290 (2008), doi: 10.1016/j.msea.2008.02.005
  • [10] A. Di Schino, L. Alleva, M. Guagnelli, Mater. Sci. Forum 715-716, 860 (2012), doi: 10.4028/
  • [11] Y. Jin, M. Bernacki, G.S. Rohrer, A.D. Rollett, B. Lin, N. Bozzolo, Mater. Sci. Forum 113-116, 120 (2013), doi: 10.4028/
  • [12] L. Lianos, B. Pereda, D. Jorge-Badiola, J.M. Rodriguez-Ibabe, B. Lopez, Mater. Sci. Forum 753, 443 (2013), doi: 10.4028/
Document Type
Publication order reference
YADDA identifier
JavaScript is turned off in your web browser. Turn it on to take full advantage of this site, then refresh the page.