Effects of cutting parameters on delamination during drilling of Polyphthalamide (PPA) Matrix Composite Material with 30% Glass Fiber Reinforcement

• Authors: F. Ficici , Z. Ayparcasi
• Languages of publication: EN

Abstracts

EN

The drilling of glass fiber reinforced plastics (GFRP) often results in damage around the drilled hole. The drilling of such composite material may generate delamination of drilled holes on workpiece. The aim of this research is to investigate the influence of the drilling parameters, such as cutting speed, feed rate and differences in cutting materials on delamination produced while drilling GFRP composite. The experimental results indicate that the feed rate is the most significant factor, followed by spindle speed and cutting tool material. The best results were obtained at lower feed rates and higher spindle speeds when using Carbide drill.

Keywords

EN

81.05.Qk; 81.05.Lg; 81.20.Wk

Discipline

• 81.20.Wk: Machining, milling
• 81.05.Lg: Polymers and plastics; rubber; synthetic and natural fibers; organometallic and organic materials(for polymers and organic materials in electrochemistry, see 82.45.Wx)
• 81.05.Qk: Reinforced polymers and polymer-based composites

• Journal: Acta Physica Polonica A
• Year: 2015
• Volume: 127
• Issue: 4
• Pages: 1118-1120

Dates

published

2015-04

Contributors

author

F. Ficici

• Sakarya University, Faculty of Technology, 54187, Sakarya, Turkey

author

Z. Ayparcasi

• Sakarya University, Faculty of Technology, 54187, Sakarya, Turkey

References

• [1] E. Kilickap, Expert Syst. Appl. 37, 6112 (2010), doi: 10.1016/j.eswa.2010.02.023
• [2] E. Brinksmeier, Ann. CIRP 39, 97 (1990), doi: 10.1016/S0007-8506(07)61011-7
• [3] H.M. Chow, S.M. Lee, L.D. Yang, J. Mater. Process Techn. 207, 180 (2008), doi: 10.1016/j.jmatprotec.2007.12.064
• [4] J.P. Davim, P. Reis, Mater. Design 24, 315 (2003), doi: 10.1016/S0261-3069(03)00062-1
• [5] I. El-Sonbaty, U.A. Khashaba, T. Machaly, Compos. Struct. 63, 329 (2004), doi: 10.1016/S0263-8223(03)00181-8
• [6] K. Palanikumar, B. Latha, V. Senthilkumar, J.P. Davim, Mater. Manuf. Process 27, 297 (2012)
• [7] NS. Mohan, SM. Kulkarni, A. Ramachandra, Mater. Proc. Technol. 186, 186 (2007), doi: 10.1016/j.jmatprotec.2006.12.043
• [8] K. Palanikumar, S. Prakash, K. Shanmugam, Mater. Manuf. Process. 8, 858 (2008), doi: 10.1080/10426910802385026
• [9] A.M. Abrao, J.C. Campos Rubio, P.E. Faria, J.P. Davim, Mater. Design 29, 508 (2008), doi: 10.1016/j.matdes.2007.01.016
• [10] T.V. Rajamurugan, K. Shanmugam, K. Palanikumar, Mater. Design 45, 80 (2013), doi: 10.1016/j.matdes.2012.08.047

Identifiers

DOI

10.12693/APhysPolA.127.1118