PL EN


Preferences help
enabled [disable] Abstract
Number of results
2012 | 122 | 3 | 485-489
Article title

Creep Behavior of a Zirconium Alloy Processed by Equal-Channel Angular Pressing

Content
Title variants
Languages of publication
EN
Abstracts
EN
A Zr-2.5 wt%Nb alloy was processed by equal-channel angular pressing and then tested under creep conditions at 623 K using a tensile stress within the range from 120 to 300 MPa. The results show conventional power-law creep with a stress exponent of n > 3 which is consistent with an intragranular dislocation process involving the glide and climb of dislocations. It is demonstrated that diffusion creep is not important in these tests. For comparison purposes, the experiments were conducted using both the unprocessed alloy and after processing by equal-channel angular pressing. It was found that under same testing conditions the measured minimum creep rates in the pressed alloy with ultrafine grain sizes were faster than in the same alloy in a coarse-grained unprocessed condition.
Keywords
Contributors
author
  • Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Zizkova 22, 616 62 Brno, Czech Republic
author
  • Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Zizkova 22, 616 62 Brno, Czech Republic
author
  • Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Zizkova 22, 616 62 Brno, Czech Republic
author
  • Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Zizkova 22, 616 62 Brno, Czech Republic
author
  • Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Zizkova 22, 616 62 Brno, Czech Republic
author
  • Physico-Technical Institute of NAS Belarus, Kuprevicha 10, 220141 Minsk, Belarus
author
  • National University of Science and Technology "MISIS", Leninskiy prospect 4, 119049 Moscow, Russia
author
  • National University of Science and Technology "MISIS", Leninskiy prospect 4, 119049 Moscow, Russia
  • A.A. Baikov Institute of Metallurgy and Materials Science of RAS, Leninskiy prospect 49, 119991 Moscow, Russia
References
  • [1] R.Z. Valiev, T.G. Langdon, Prog. Mater. Sci. 51, 881 (2006)
  • [2] Y. Zhu, R.Z. Valiev, T.G. Langdon, N. Tsuji, K. Lu, MRS Bull. 35, 977 (2010)
  • [3] V.F. Terentyev, S.V. Dobatkin, S.A. Nikulin, V.I. Kopylov, D.V. Prosvirnin, S.O. Rogachev, I.O. Bannykh, Kovove Mater. 49, 65 (2011)
  • [4] F.R.N. Nabarro, Reports of a Conference on Strength of Solids, The Physical Society, London 1948, p. 75
  • [5] C. Herring, J. Appl. Phys. 221, 437 (1950)
  • [6] R.L. Coble, J. Appl. Phys. 34, 1679 (1963)
  • [7] I. Charit, K.L. Murty, J. Nucl. Mater. 374, 354 (2008)
  • [8] M. Pahutová, J. Čadek, V. Černý, J. Nucl. Mater. 61, 285 (1976)
  • [9] M. Pahutová, K. Kuchařová, J. Čadek, J. Nucl. Mater. 131, 20 (1985)
  • [10] R. Kishore, J. Nucl. Mater. 385, 591 (2009)
  • [11] W. Li, R.A. Holt, J. Nucl. Mater. 401, 25 (2010)
  • [12] T.A. Hayes, M.E. Kassner, R.S. Rosen, Metall. Mater. Trans. A 33, 337 (2002)
  • [13] J. Čadek, Creep in Metallic Materials, Elsevier Science Publisher, Amsterdam 1988
  • [14] T.G. Langdon, Acta Metall. Mater. 42, 2437 (1994)
  • [15] H.G. Kim, Y.H. Kim, B.K. Choi, Y.H. Jeong, J. Nucl. Mater. 359, 268 (2006)
  • [16] R. Lagneborg, Scr. Met. 7, 605 (1994)
  • [17] P.M. Sargeant, M.F. Ashby, Scr. Met. 16, 1414 (1982)
  • [18] Y. Amoyal, S.V. Divinski, L. Klinger, E. Rabkin, Acta Mater. 56, 5500 (2008)
  • [19] A.H. Chokshi, Mater. Sci. Eng. A 483-484, 485 (2008)
  • [20] M. Kawasaki, I.J. Beyerlein, S.V. Vogel, T.G. Langdon, Acta Mater. 56, 2307 (2008)
  • [21] M. Kawasaki, V. Sklenicka, T.G. Langdon, J. Mater. Sci. 45, 271 (2010)
  • [22] M. Kvapilova, V. Sklenicka, J. Dvorak, P. Kral, Key Eng. Mater. 465, 382 (2011)
  • [23] M. Kawasaki, V. Sklenicka, T.G. Langdon, Kovove Mater. 49, 75 (2011)
Document Type
Publication order reference
Identifiers
YADDA identifier
bwmeta1.element.bwnjournal-article-appv122z3p15kz
JavaScript is turned off in your web browser. Turn it on to take full advantage of this site, then refresh the page.